Post-Apocalypse Terrain Build (with biscuit tins)

I recently had the pleasure of attending the Wargames Illustrated 7TV Apocalypse Day held in the wonderful surroundings of Wargames Foundry on the outskirts of Newark.
The day was all about having fun testing out the new 7TV variant rules for gaming in a wide variety of post-apocalypse settings.  Although aimed at a wide variety of sub-genres within the PA setting, one of the key additions to the core game was expanded vehicle and vehicle combat rules.

Therefore preparation for the day included building a suitable vehicle to carry your cast and fight it out with.

Some excellent terrain and scenery was provided on the day, but coming back I had the real desire to knock together something of my own.

I’d been hoarding some bits and pieces recently and what better to fight over in the ‘white line nightmare’ of the future than the precious gasoline.

So behold the start of the ‘biscuit tin oil refinery’…

37019438_10156628322805555_110758552204738560_o-770

The fundamentals of this build are biscuit tins.  First thing before anything else could be started then was to eat all the biscuits. An arduous task, but one I achieved with bravery and resolve.

Many years ago I backed the first Mantic Deadzone Kickstarter, I never really got into the game and off loaded most of it, apart from the excellent Battlezones scenery bits and pieces.  To dress up the basic tins which would act as the silo/tank I used some of the Battlezones ladders and a few other bits and pieces.

To provide the upright struts around the tank (and to make it look less biscuit tin like) I used off cut pieces of plastic sprues.

To provide a base I used some ‘magazine dividers’ which are effectively quite thick plasticard.

The plasticard base was trimmed to make it look less like a piece of stationary, and then marked out with areas where paths and pools of ‘toxic waste’ would be placed.

A mix of modelling sand and PVA was whipped up and slopped on (technical term), leaving space for the marked out areas.

Taking advantage of the very un-British summer this was left out in the blazing heat for a while to set.

I wanted to go with a downbeat weathered look and knew I wanted it to look rusty and abandoned.  First base colour then was Army Painter Chaotic Red to provide that underlying feel.


Light sprays of Russian Green were then used to add the primary hues, leaving the dark red showing underneath.

2018-07-1416.34.16_preview.jpeg

After having left it to dry for a while I then scuffed up key areas using a kitchen scouring pad to scratch off layers of paint to try and reveal the underlying red (and in some cases original biscuit tin colours).


I used (the now sadly out of production) Modelmates paint on rust effects to properly weather it up, concentrating on scuffed areas,  the areas where the two original tins met (rather than hiding the join I thought I’d make use of it.  I also concentrated on the areas where the ‘pipes’ joined the base of the silo.  In addition the ladders were rusted up in key areas.


A covering of Plastic Soldier Company Dirt Brown weathering spray was then used all over and after a few minutes was smeared and sponged using some old blister pack foam.

The foam was then broken out again to use the ‘sponging chipping’ technique using a dark brown paint.

Having completed the bulk of the paint work on the silo itself, I set about the base.  A generous coat of brown artists acrylic paint was applied followed by an initial dry brush.  This was then followed up by painting on some Army Painter Strong Tone dip.

5b55c61d4adb4-5b55c61d4adf02018-07-142017.01.55_preview.jpeg.jpg-770

Following (the faster than usual due to the summer heat) drying time of the Quickshade I then did a  lighter brown drybrushe followed by a light dusting of Army Painter Skeleton Bone.

Wasteland tufts from Army Painter were used to add detail (especially around the edges of the structure).

I’d previously left some gaps in the original sand-PVA mix on the base board with the intention of using these as pools of some sort.  In fitting with the wasteland setting these became toxic waste deposits, so I finally found a use for that pot of Citadel Nurgle’s Rot technical paint I’ve had lying around for years.

The space I had left for pathways was painted dark grey and then roughly stipled with a lighter grey to give the impreseion of gravel or worn tarmac.

Pipe work and barrels were picked out with Foundry Blackened Barrel (my absolute favourite metallic paint – ideal for guns – as it says on the tin!).  A bit more ‘toxic sludge’ was added to the top of one of the barrels.

2018-07-1608.39.30_preview.jpeg

Finally I dived into the bits box of decals and applied some warning signs in key locations and chose the deliberately ominous ’13’ for the silo’s primary identification!

2018-07-1608.38.28_preview.jpeg2018-07-1608.39.07_preview.jpeg

And that about does it, all that remains is to seal down the decals and apply a bit of weathering to them.

I’ll be trying something similar again (this time with laundry pod containers) in preparation for a table on which to play 7TV Apocalypse!

I originally published this article as a Project Blog using the new functionality on Beasts of War.  I’d highly recommend folk check this community and feature out.  It’s a great way to share ideas and get feedback on any hobby related activities.  (To access the projects functionality you will need to sign up as a ‘backstage member’, there is a free 7 day trial if you want to try it out).

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

w

Connecting to %s